Mercedes-Benz Forum - Reply to Topic
Topic: Timing Chain Replacement Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the Mercedes-Benz Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
06-07-2019 06:09 PM
rudeney RM European and Pierburg parts should be good. Look at the diagram and swap two solenoids - on with an error, on without. Erase codes, and then see what returns. If the error stays with he solenoid, then you have the answer. If not, then another thing to try is a couple of oil changes (you can use a cheap oil) combined with a few hours of HARD driving and revving. The adjusters are operated hydraulically with engine oil and I have seen dirty oil cause this.
06-07-2019 11:31 AM
ntvnyer I had this done on my 2003 a couple of years ago around 80-85K miles.
In the NYC metro I paid about 1500 but that included the whole job with guides and a tensioner. The kits for sale including all the parts run between $177 (without Tensioner) and $300 (with tensioner) for good FEBI parts at FCP euro. I would not suggest the chain weave as the guides and tensioner are in my opinion a necessary part of the job.

I went though the exact same diagnostic process but I do not recall my codes, and unfortunately the magnets and other parts that came off my car were probably good. The techs I use when I can't handle something followed the same logic as you did.

My symptoms we a sudden change in idle one day and then bumpy idle and poor drivability unless I applied full throttle. even at full the car was about 70%. The tech told me that my chain had jumped and that my timing was off by about 10 degrees, but I have no way of verifying this. I can tell you that the chain removed was noticeably longer than the new one.
I saved all the magnets and the cam sensors for future us as I believe them to be good. I used original MB parts for the magnets because the cost difference was not that big.
06-07-2019 07:55 AM
emarkham Ordered parts from RM European Auto Parts ( Denver Colorado )

Camshaft Adjuster Magnet
Manufactor: Pierburg
-----------------------------
Camshaft Position Sensor
Manufactor: Bosch
----------------------
Harness
Manufactor: Mercedes Benz

I'm a DIY with lack of prescribed testing procedures for said parts
06-06-2019 07:52 PM
rudeney I really don't think this is a timing chain issue. These are all codes that indicate bad camshaft adjuster solenoids (magnets):



Where did you get the solenoids?
06-06-2019 10:00 AM
emarkham
Timing Chain Replacement

2007 Mercedes Benz 2007 C230 Sport
( W203 with M272 E25 (2.5L V6 ))
I replaced
all camshaft position sensors
all camshaft adjuster magnets
with inclusion of new harnesses

The CEL assertions are now
P0011, P0014, P0015, P0022, P0025

Basically (over time and more drive sessions )
both camshaft A/B banks
with advanced/retarded timings will manifest.

Balance Shaft engine problem factory addressed:
engine serial number includes engineered fix

I believe I am looking at a timing chain replacement
( I hear there is a existing procedure ( ~$1500ish )
that weaves in the new chain elements without the extensive
( ie labor intensive) opening up of engine

Engine runs smooth with noted hesitation (lag) but once
engaged it acquires power band performance.
Slight rattle appears on startup only ( oil pump delivery window )
No further rattle as if from a timing chain tensioner problem.

I'm in SF Bay Area and looking for reference to a talented mechanic
that can perform the timing chain replacement.

Recommendations ( or any birddogging of mechanical knowhow
will be appreciated )

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 

Title goes here

close
video goes here
description goes here. Read Full Story
For the best viewing experience please update your browser to Google Chrome